New in version 2.6.
The below requirements are needed on the host that executes this module.
Parameter | Choices/Defaults | Comments | |
---|---|---|---|
ignore_down_response bool |
| Specifies that the monitor allows more than one probe attempt per interval. When yes , specifies that the monitor ignores down responses for the duration of the monitor timeout. Once the monitor timeout is reached without the system receiving an up response, the system marks the object down.When no , specifies that the monitor immediately marks an object down when it receives a down response.When creating a new monitor, if this parameter is not provided, then the default value will be no . | |
interval | Specifies, in seconds, the frequency at which the system issues the monitor check when either the resource is down or the status of the resource is unknown. When creating a new monitor, if this parameter is not provided, then the default value will be 30 . This value must be less than the timeout value. | ||
ip | IP address part of the IP/port definition. If this parameter is not provided when creating a new monitor, then the default value will be '*'. | ||
name required | Monitor name. | ||
parent | Default: /Common/tcp_half_open | The parent template of this monitor template. Once this value has been set, it cannot be changed. By default, this value is the tcp_half_open parent on the Common partition. | |
partition | Default: Common | Device partition to manage resources on. | |
password required | The password for the user account used to connect to the BIG-IP. You may omit this option by setting the environment variable F5_PASSWORD .aliases: pass, pwd | ||
port | Port address part of the IP/port definition. If this parameter is not provided when creating a new monitor, then the default value will be '*'. Note that if specifying an IP address, a value between 1 and 65535 must be specified | ||
probe_attempts | Specifies the number of times the system attempts to probe the host server, after which the system considers the host server down or unavailable. When creating a new monitor, if this parameter is not provided, then the default value will be 3 . | ||
probe_interval | Specifies the number of seconds the big3d process waits before sending out a subsequent probe attempt when a probe fails and multiple probe attempts have been requested. When creating a new monitor, if this parameter is not provided, then the default value will be 1 . | ||
probe_timeout | Specifies the number of seconds after which the system times out the probe request to the system. When creating a new monitor, if this parameter is not provided, then the default value will be 5 . | ||
provider (added in 2.5) | Default: None | A dict object containing connection details. | |
ssh_keyfile | Specifies the SSH keyfile to use to authenticate the connection to the remote device. This argument is only used for cli transports. You may omit this option by setting the environment variable ANSIBLE_NET_SSH_KEYFILE . | ||
timeout | Default: 10 | Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error. | |
server required | The BIG-IP host. You may omit this option by setting the environment variable F5_SERVER . | ||
user required | The username to connect to the BIG-IP with. This user must have administrative privileges on the device. You may omit this option by setting the environment variable F5_USER . | ||
server_port | Default: 443 | The BIG-IP server port. You may omit this option by setting the environment variable F5_SERVER_PORT . | |
password required | The password for the user account used to connect to the BIG-IP. You may omit this option by setting the environment variable F5_PASSWORD .aliases: pass, pwd | ||
validate_certs bool |
| If no , SSL certificates are not validated. Use this only on personally controlled sites using self-signed certificates.You may omit this option by setting the environment variable F5_VALIDATE_CERTS . | |
transport required |
| Configures the transport connection to use when connecting to the remote device. | |
server required | The BIG-IP host. You may omit this option by setting the environment variable F5_SERVER . | ||
server_port (added in 2.2) | Default: 443 | The BIG-IP server port. You may omit this option by setting the environment variable F5_SERVER_PORT . | |
state |
| When present , ensures that the monitor exists.When absent , ensures the monitor is removed. | |
timeout | Specifies the number of seconds the target has in which to respond to the monitor request. If the target responds within the set time period, it is considered up. If the target does not respond within the set time period, it is considered down. When this value is set to 0 (zero), the system uses the interval from the parent monitor. When creating a new monitor, if this parameter is not provided, then the default value will be 120 . | ||
transparent bool |
| Specifies whether the monitor operates in transparent mode. A monitor in transparent mode directs traffic through the associated pool members or nodes (usually a router or firewall) to the aliased destination (that is, it probes the ip -port combination specified in the monitor).If the monitor cannot successfully reach the aliased destination, the pool member or node through which the monitor traffic was sent is marked down. When creating a new monitor, if this parameter is not provided, then the default value will be no . | |
user required | The username to connect to the BIG-IP with. This user must have administrative privileges on the device. You may omit this option by setting the environment variable F5_USER . | ||
validate_certs bool (added in 2.0) |
| If no , SSL certificates are not validated. Use this only on personally controlled sites using self-signed certificates.You may omit this option by setting the environment variable F5_VALIDATE_CERTS . |
Note
pip install f5-sdk
.- name: Create TCP half-open Monitor bigip_gtm_monitor_tcp_half_open: state: present ip: 10.10.10.10 server: lb.mydomain.com user: admin password: secret name: my_monitor delegate_to: localhost - name: Remove TCP half-open Monitor bigip_gtm_monitor_tcp_half_open: state: absent server: lb.mydomain.com user: admin password: secret name: my_monitor delegate_to: localhost - name: Add half-open monitor for all addresses, port 514 bigip_gtm_monitor_tcp_half_open: server: lb.mydomain.com user: admin port: 514 password: secret name: my_monitor delegate_to: localhost
Common return values are documented here, the following are the fields unique to this module:
Key | Returned | Description |
---|---|---|
interval int | changed | The new interval in which to run the monitor check. Sample: 2 |
ip string | changed | The new IP of IP/port definition. Sample: 10.12.13.14 |
parent string | changed | New parent template of the monitor. Sample: tcp_half_open |
probe_attempts int | changed | The new number of attempts the system will make in checking the monitor probe. Sample: 10 |
probe_interval int | changed | The new interval in which the system will check the monitor probe. Sample: 10 |
probe_timeout int | changed | The new timeout in which the system will timeout the monitor probe. Sample: 10 |
timeout int | changed | The new timeout in which the remote system must respond to the monitor. Sample: 10 |
This module is flagged as preview which means that it is not guaranteed to have a backwards compatible interface.
This module is flagged as community which means that it is maintained by the Ansible Community. See Module Maintenance & Support for more info.
For a list of other modules that are also maintained by the Ansible Community, see here.
Hint
If you notice any issues in this documentation you can edit this document to improve it.
© 2012–2018 Michael DeHaan
© 2018 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.7/modules/bigip_gtm_monitor_tcp_half_open_module.html